I just bought a AKG C680 BL Microphone (Jack stereo Native and XLR adaptator) to record my voice under Windows.
As i plug the microphone, i can hear some noisy sound but after i can't hear my voice at all... (i have to scream in the microphone to hear a little of my voice...). It sounds like there is an amplification problem. I also plugued it in my Osprey XLR card , but stil no hear voice at all...
Before sending the microphone back to the vendor, i would be glad to read some specialist advises
Here are the microphone specs :
QUOTE
The C 680 BL is a cost-efficient tabletop microphone for inconspicuous installation. The transducer shock mount minimizes knocking noise pickup from the table. The supplied strip of special adhesive tape allows you to fix the microphone temporarily on a table without staining the table or leaving any residue after removal.
Preferred uses include conferencing, lectern, or places of worship.
Features:
* Small and inconspicuous boundary layer microphone
* Shock mounted transducer
* Cardioid polar pattern
* Easy to repaint
* Integrated phantom power adapter
* 3 Pin XLR connector on 3m (10ft) cable
Specifications:
* Transducer Principle: Condenser prepolarized
* Frequency Range: 60–20,000 Hz
* Polar Pattern: Cardioid
* Sensitivity at 1,000 Hz: 23 mV/Pa (-32 dBV) 30 mV/Pa (-30 dBV)
* Equivalent Noise Level: < 27 dB-A
* Sound Pressure Level for 1% THD: 115 dB
* S/N Ratio (A-weighted): > 67 dB
* Electr. Impedance: < 200 ohms
* Load Impedance: > 2000 ohms
* Power Requirement: 9–52 volts phantom powering
* Connector: 3-Pin XLR type
* Cable Length: 3 m (10 ft.)
* Finish: Non-reflective black
* Size: 3.8 x 2.6 x 0.8 in. (97 x 67 x 20 mm)
* Net/Shipping Weight: 3.5/10 oz. (100 g/284 g)
* Included Accessories: Phantom power adapter, adhesive tape
* Optional Accessories: B 18 Battery power supply N 62 E AC Power supply
Preferred uses include conferencing, lectern, or places of worship.
Features:
* Small and inconspicuous boundary layer microphone
* Shock mounted transducer
* Cardioid polar pattern
* Easy to repaint
* Integrated phantom power adapter
* 3 Pin XLR connector on 3m (10ft) cable
Specifications:
* Transducer Principle: Condenser prepolarized
* Frequency Range: 60–20,000 Hz
* Polar Pattern: Cardioid
* Sensitivity at 1,000 Hz: 23 mV/Pa (-32 dBV) 30 mV/Pa (-30 dBV)
* Equivalent Noise Level: < 27 dB-A
* Sound Pressure Level for 1% THD: 115 dB
* S/N Ratio (A-weighted): > 67 dB
* Electr. Impedance: < 200 ohms
* Load Impedance: > 2000 ohms
* Power Requirement: 9–52 volts phantom powering
* Connector: 3-Pin XLR type
* Cable Length: 3 m (10 ft.)
* Finish: Non-reflective black
* Size: 3.8 x 2.6 x 0.8 in. (97 x 67 x 20 mm)
* Net/Shipping Weight: 3.5/10 oz. (100 g/284 g)
* Included Accessories: Phantom power adapter, adhesive tape
* Optional Accessories: B 18 Battery power supply N 62 E AC Power supply
